ТЕХДОКУМЕНТАЦИЯ > Hi_SHARP

HS-CC600_610_620

The first part: Construction
High-speed dome is very popular now. It has high speed, low noise and long life. The
good construction, convenient installations are the product’s advantages. It is used in
industry, business, government department and entertainment places.
1Product introduction

1.jpg

2.jpg

2Connection Assembly
 Step 1 :
 Fix base 1 on the ceiling with screw 8
 Step 2 :
 Connect the power cable to power outlet (numbered 12) and video cable to video outlet
 (numbered 10)
Please connect correctly. Don’t energize incorrectly,
 which will injure electric organ
Step 3 :
 Adjust DIP switch 11

3.jpg

Step 4
 Mount camera on the camera bracket, then fix the camera with M2 screw numbered 6.
 Step 5 :
 Check every connection again to make sure everything is secured.
 Step 6 :
 Mount the dome, then clean it.
  Dome and top housing mount.
 Connect dome and top housing ,Please see the connection figure.
Put the ” top housing” up ,and turn the top housing slowly.
 Through φ11 core and top housing core, can see camera bracket screw core.
 Put 4-M3×5 into it.
 After connecting the dome and top housing, put 3 screws on the dome, into the ceiling,
 and turn 30°.
  High-speed dome is so small and it is so easy installation that it has been used in many
 places, such as building, bank, school, parking lot, and so on .
 • Small
 • ABS material
 • Easy installation
 • High sensitivity
 • High resolution
 • High speed
 • Low and steady speed
The second part: Electronic Specification
 1Introductions
 1.1 Important safeguards and warning.
 Prior to installation and use of this product, the following warnings should be
 observed.
 1 Installation and servicing should only be done by the qualified service personnel and
 confirm to the local codes.
 2 Check this product and make sure it is used indoor or outdoor.
 3 The installation method and material should be capable of supporting the weight of the
 enclosure, pan/tilt camera lens combination.
 This symbol indicates that there are important operating and maintenance
 instructions in the literature accompanying this unit.
 This symbol indicates that dangerous voltage that a risk of electric
 shock is present within this Unit.
 CAUTION: Risk of electric shock. Do not open. !
1.2 Regulatory Notices
 Note: This equipment has been tested and found to comply with the limits of a class A
 digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide
 reasonable protection against harmful interference when the equipment is operated in a
 commercial environment. When this equipment generates and uses, it can radiate radio
 frequency energy and if it is not installed and used in accordance with the instruction manual,
 it may cause harmful interference to radio communicating. Operation of this equipment is in
 a residential area. In case it is likely to cause harmful interference the user will be required to
 correct the interference at his own expense.
1.3 Instructions
 This box contains one dome driver and one installation operation manual. Before you
 start, please inspect all parts carefully and save the shipping carton boxes and inserts.
 1.4 The main features
  Pan Movement: 360ºcontinuous pan rotation , 90ºin tilt , 180º auto flip
  There are 64 programmable preset points available.
  Low speed is available for catching on the zoomed target accurately.
  Auto tour scan (call the No. preset 70)
  Camera menu can be turned on by setting 95 preset function.
  Privacy Zone Mask: 3 Rectangles could be set by setting preset point from 1th to 6th
 point.
  Manual zoom in/out.
  Manual/Auto focus and Iris ON/OFF by OSD menu
  Manual/Auto black and white switching
  Manual Focus & Menu Iris lens speed is adjustable
  Auto/Manual white balance
  Manual/Auto backlight compensation
  Cruise through preset points.
  Cruising speed is adjustable5°/S, 60°/S,120°/S
  Dwell time is changeable (5S, 10S, 30S)
  Rolling speed between 1~64
  Inner mount preventing from surge or lightning strike
  Easy to install
  When power lost, auto protection function turns on immediately
  RS-485 communication port
 Technical data
 1. Voltage 12VDC(±10%) Linear power
 2. Power ≤10W
 3. Pan Turn speed 0.3º ~ 120º /s
 4. Tilt Rotation Speed: 0.3º ~ 57º /s
 5. Manual tilt scale ≤90º
 6. Scan scale 360º Continuously
 7. Preset 64 preset point
 8. Preset find time <3S
 9. Preset speed120º/S
 10. Zoom find time <1.65 S
 11. Scan Precision 0.225º±0.03º
 12. Signal Format PAL / NTSC
 13. Picture element 752(H)×582(V)
 14. S/N ratio >48dB
15. Communication port RS-485
 16. Baud Rate 2400\4800\9600
 17. Suitable temperature(Indoor)  -20~50 for indoor, -45~50 for outdoor.
 2Installation
 2.1 Dome installation:
 There are one video connection, one power, and one communication port boards one
 the dome.

4.jpg

Connection: Put video cable into video outlet and connect the power cable and
 communication cable (see the following chart)
2.2 Dome address
 There are two DIP switcher on the dome base. (see the following chart)

5.jpg

1. Switch 7 and 8 is the baud rate selector                               1. Every dip 1 switch to ON to increase command transfer quality.
 2. Switch 1-6 is address selector
2.3 Set baud rate
 Baud rate:2400/s, 4800/s,9600/s
3Operation
 Before power on, please check the power cable connection, communication cable
 connections are secured.
 3.1 Level and tilt control
 High-speed dome, level and tilt speed is subject to the joystick, and the
 speed is 0.3º ~ 120º /s.
 3.2 Auto flip
 When camera tilt down 90º, the dome rotates 180º automatically in level.
 3.3 Zoom
 The dome can support an object up to 128×,64×,32×,16×,8× camera. Press
 the zoom button to zoom in the picture until the monitor display the zoomed picture that you
 need. Zoom speed can be controlled by remote controller.
 3.4 Auto/Manual Focus
 Focus speed can be controlled by remote controller
 3.5 OSD FUNCTION
 Set preset point 75 to turn on OSD ICON. The camera parameters will be
 shown on the below left side of the display point to turn OSD ICON.
 3.6 Preset functions
 The dome can set 64 preset positions, which are numbered 1-32 and
 35-66. Refer to your control system documentation for programming presets.
 When doing a preset operation, the amount of error in moving to the pan and tilt positions is
 under 0.3º. Preset 33 is named turnover command. When using preset 33, high-speed
 dome circumrotate 180ºin pan. Preset 34 is the “pan zero” command. When using preset 34,
 high-speed dome return reset position.
 This function may make the camera transfer prior and defined region
 image. Meanwhile, it will automatically adjust the focus and zoom.
The following presets are reserved for special function.
 Preset Function
 1-32 Preset
 33 Turnover (Horizontal Pan 180º)
 34 Pan zero
 35-66 Preset
 Call 75 OSD ON
 Call 76 Star Auto Tour
 Set 77 Clear All Preset
 Set 92 left limit
 Set 93 Right limit
 Set 94 Camera initial data
 Set 95 Enter/ESC the camera OSD Menu
 Call 96 Line scan & Auto tour stop.
 Call 99 Line scan
 3.7 Auto scan
 Call preset 99 functions to start line scanning, and the scanning stops automatically
 when control system runs other control commands.
 Set preset 92 point, it sets the left limit, Set preset 93 point, it sets the right limit. When
 start to line scan, it will rotate between these two preset points. And, It automatically stops
 when receives the valid direction commands.
 3.8 Cruise through the Presets
 Our High-speed Dome support one group (16 points) cruise paths.
 Cruise from 1-16 Preset .If there is the preset , which has not been deleted, it will be
 ignored. The pause time is 5S,10S or 30S. The cruise speed is 5°/S,60°/S,120°/S.
 • Confirm the places you need, and input to 1-16 preset
 • Setup the pause time
 Operate Pause Time
 Setup No. 70 preset 5S
 Setup No. 71preset 10S
 Setup No. 72 preset 30S
 • Setup cruising speed
 Operate Cruising Speed
 Setup No. 73 preset 5°/S
 Setup No. 74preset 60°/S
 Setup No. 75 preset 120°/S
 • Startup Cruise Function
3.9 Camera menu transferring
 Program 95 to camera list and you can choose the list and you can press the Focus Far
 or Focus Near button.
 When the cursor moves to some item, you can press that button to change it.
 After that, you can press the Focus Near. The same as the above, you can modify other
 items. After that, you can press 95 preset to close it.
 3.10 Day Iris & Night Use the (only for Sony camera)
 Choose Auto/OFF Iris by the camera list .If choose Auto, can control the Iris by the
 button [OPEN] and [CLOSE] on the keyboard.
 Choose Auto/Night On/Night off by the camera list. When choose Auto Night Function,
 the Iris must be auto. Otherwise,
 this function is invalid.
 Camera Menu Introduction
 1Menu definition
 95 & [PRESET] for two seconds :open or close the Menu
 [FAR]: Setup Menu
 [WIDE]: Page down
 [TELE]: Page up
 [OPEN]:Increase the Menu Scale
 [CLOSE]: Decrease the Menu Scale
 2Use Guide
 1 95&[PREST] for two seconds: Open or close the Menu, Open the menu, Page up or
 Page down by press [WIDE] or [TELE] Choose the item you need.
 2 When the item with“”,can adjust the Parameter value by Pres [OPEN]or[CLOSE]
 3 When SAVE=YES, close the menu. The parameter value can be saved when the
 power is supply is off
3.11 Low Lux (without CC600)
During the night, we can manual turn on B/W mode that can keep the picture more clear
 even in low Lux condition.
 To switch mode between color mode and B/W mode, we press[ turn on/off Iris] to
 alternate these two mode.
 3.12 Back light compensation
 This function can be use in the strong back light circumstance, such that the dark place
 of the image can have good picture quality.
 3.13 Privacy Zone Mask
 Privacy Zone allows a user to program specific areas that cannot be viewed by the
 operator of the dome system. And, the area has been masked in the picture can not be
 reconstructed.
 Privacy Zone mask allows user to program up to 18 user-defined areas that
 cannot be viewed by the operator of the system. Therefore, for 6 setting point, each setting
 point can have 3 privacy mask zone area.
 To set a privacy zone, there are four hot keys support:
 Press 79: Enter the Privacy Zone Mask Mode
 Press 80: Select Specific Mask Area
 Press 81: Exit the Privacy Zone Mode
 Press 81: Clear the Whole Mask Block
 Procedure:
 1. Call the Pre-Set Point (1–6) before setting the Privacy Zone Mask
 (Please see the Pre-Set Point Setting function).
 2. Move the Joystick to bring the Camera to the desired Area.
 3. Press 79 to enter the Privacy Zone Mask Mode
 4. There will be a Block Mask at the Up-Left side in the Screen.
 5. Move the Joystick to the Desired Start Point.
 6. Press 80 to Confirm the Start Point. Move the Joystick to select the
 Desired Mask Area.
 7. Press 81 to Exit the First Mask Area setting.
 8. Repeat Procedure 3 to 7 to set up the whole Privacy Zone Mask of the
 Pre-Set Point.
 9. Save the Setting before Exit
1. Speed Dome

6.jpg

Speed Dome                                               Cover                                                     Bracket
Embeded Mounting
 Step 1, To revolve the tray of the Step 2, The picture shows out the
 Camera base cavity of the camera base.
 Step 3, Insert the screwdriver inside. Step 4, Turn the camera body clock
 Wise slowly.
 Clockwise: Open
 Left
 Right
 Step 5, Hold the camera body to Step 6, Hold the dome body then
 Remove. Take it out.
 Step 7, A dip switcher is on the rear panel Step 8, High Speed Dome address
Of the dome base. Every speed Up to 64 ID (See page 7)
 dome must give it an ID, like we give it a name.
 In the dome there is DIP switch, on
 the base (see the following chart)
 Step 9, Check the ID and then put it back, Step 10, The picture shows out the
 There are 3 immobile fillister for the cavity of the camera base.
 Screw inside the dome base cover.
 Step 11,Insert the screwdriver inside. Step 12, Turn the camera body anticlockwise slowly.
 Anti-clockwise: Close
 Step 13, Attach 3 screws nuts of the speed Step 14, Tighten the 3 screws into the
 Dome and dome cover screw nuts setp.
 Step 15, Make sure the Speed Dome has 5 lines:
Thin lines-red(+)and black(-): power cord
 -Yellow(+)and grey(-):control line
 Thick line -Black line is video line
 Step 16, Tighten lock the 2 holes. Step 17, Combine the speed dome and
 the bracket and make sure
 those lines are outside of the
 bracket. Then hole are aim.
 Step 18, Make sure the position then drill Step 19, After make sure it and drill
 holes of the chosen area.
 Step 20, Tighten the screw on the wall Step 21, Make sure all the lines are
 Connecting together.
 Step 22, Tighten the last screw on the Step 23, Finish your installation bracket.

Назад в раздел